Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
Just how do you actually feel on the subject of Installing A Bathtub?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Installing a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably challenging project. If the old bathtub is readily easily accessible, the task can relocate immediately; if you need to open a wall to remove the old bathtub and also position the brand-new tub, the task is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub and set in the brand-new one. See to it you have certified on your own for the job and fit trying it. Instead of employing a service provider to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This short article will certainly aid you set up a new bath tub in your washroom if you have already purchased a new tub and also don't require to transform the arrangement of your previous supply of water pipes.
Your devices as well as material list must make up the following:
Getting ready for the Setup
To start with, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its final setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Using both wood boards under its feet, put the tub in the needed position. The wood boards are useful in equally spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub up until the spirit level reviews degree.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water and check all joints and new pipework for leaks and tighten them if necessary. Load the bath tub and likewise check the overflow outlet and the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub should wait till the bath tub has actually been utilized a minimum of when as this will resolve it into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in position with the producer offered backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a stiff seal, creating the water to permeate the wall between the bathroom and the tiling, leading to difficulties with moisture and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the tub is in use. The sealer can fracture fairly very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the market. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very enthusiastic about How to Install a Bathtub and I'm hoping you appreciated our blog post. In case you enjoyed reading our page please remember to pass it around. Thank you for your time. Come back soon.
Give Me A Quote! Report this page